Pont élévateur ciseaux TyreON TSC4000X2iXL In floor scissor lift - Double extensions - 12 cm i neuf

Capacity 4000 kg
Lifting height 198 cm (186 cm net)
Drive 2.2 kW Electric-hydraulic
Type Fully automatic - Heavy duty
Platforms 148,5 - 230,5 cm - Double extensions
► Hydraulic mechanical safety lock
► Safety and overload valves in the cylinder systems
► No air required - immediate descent
► Auto-stop at 25 cm + slow descend
► IR synchronization monitoring
► Tip-lever system
► Scissor axles with bushings, low-wear
Delivery incl. Floor bolts and + rubber blocks (4)
Voltage 400V
Package L160 x W80 x H42 cm - 900 kg
Controller L48 x W41 x H116 cm - 50 kg
Certification CE / TUV Directive EN1493:2010 Vehicle Lifts
Colour As of 2024, completely anthracite grey RAL7016
3 models available
TSC4000X2 iXL Inground - 12 cm
TSC4000X2 XLLR 4 x L100 cm ramps
TSC4000X2 XLSR 4 x L56 cm ramps

TyreON supplies the TSC4000X2iXL with hydromechanical technology.
No compressed air required, low maintenance and a safe direct lowering of the platforms as soon as the down button is pressed is characteristic of this technology.
The scissorlift rises immediately with full force thanks to the tip-lever system and two hydraulic cylinders per platform.
Thanks to the extendable tables with a length of 148.5 to 230,5 cm, this scissor lift is suitable for lifting small and large passenger cars, SUVs, commercial vehicles and buses with short, long and multiple extended chassis up to 4T.
No more crawling under the car to have to move the extensions; the lift tables are alreadyextendable on both sides in the lowest position. (in the floor)
A heavy hydraulic pump unit provides the 4 cylinders with hard chromed piston rods with the necessary lifting force.
Installation depth only 12 cm
The platforms can be extended on both sides, even with the carlift in the lowest position (in the floor!)
Large working range from very short to very long wheelbase
Hydromechanical locking with direct lowering (no compressed air required)
24V all-in-one controller, can be placed on both sides of the carlift (max. 2.5 m)
Solid steel scissors
With tip-lever system

Finished with powder coating
Hydraulic synchronisation control monitored by IR photocell
With the 66 cm wide platforms, it's easy to drive thevehicle on the lift
Heavy 2.2 kW hydraulic pump with load-dependent lowering valve
2 cylinders with hard chrome-plated piston rods per lifting platform
Very easy to use and maintain
Installation with system-integrated ventilation and very precise levelling of the runways
The hydraulic system is vented, and the platforms are levelled with one button on the control panel
This inground scissorlift is easily mounted in two 12 cm deep recesses in a concrete floor and is connected to the controller with a customised hose set.

The carlift stops immediately at a height difference of 1.5 cm or more between the two platforms
The scissorlift stops if someone walks between the tables during lifting or lowering
Optical and acoustic signal when lowering
Auto-stop at a height of 25 cm (slow descending by pressing the down button again)
A height switch ensures the motor stops automatically when the lift reaches the highest point
Procedure for lowering in the event of a power failure
A pressure relief valve prevents damage if a vehicle is too heavy

The hydromechanical lock prevents the inground carlift from lowering in the event of a hose rupture
Delivery of the double installation bridge
The TyreON TSC4000X2iXL recessed double scissor lift and the controller have been functionally tested and then packed together with:
A set of anchoring bolts
Custom-made hydraulic hose set + accessories
4 heavy steel caps for mounting in the recesses
4 rubber lifting blocks(L12 x W16 x H4 - cm)
The installation and operating manual
Hydraulic oil is not included - 15 Liters of HV-ISO-32 can be ordered optionally
Installation dimensions
Internal dimensions of recess lift section 1-L2325 x W690 x H120 mm
Internal dimensions of recess lift section 2-L2325 x W690 x H120 mm
Pipe diameter lift section 1 to liftsection 2Ø 6 cm(distance maximum 790 mm)
Pipe diameter to controller Ø 6 cm(distance maximum 3500 mm)
TSC4000X2iXL In floor scissor lift - Double extensions - 12 cm installation depth - Hydromechanically locked - No compressed air required - 4T
The price is excluding VAT and delivery costs.